Shark Vacuum Cleaner Navigator Vacuum User Manual

4.2

Out of 13 Ratings

Owner's of the Shark Vacuum Cleaner Navigator Vacuum gave it a score of 4.2 out of 5. Here's how the scores stacked up:

  • Reliability

    4.31 out of 5

  • Durability

    4.25 out of 5

  • Maintenance

    3.92 out of 5

  • Performance

    4.42 out of 5

  • Ease of Use

    4.31 out of 5
of 9
 
10
TOLL FREE: 1-800-798-7398
11www.sharkclean.com
English
Checking for Blockages
Blockages may cause your vacuum
to overheat and shut down. If
this occurs, clear the blockages,
then follow the instructions for
Resetting the Motor Thermostat
on page 11.
IMPORTANT: Never insert sharp
objects into any opening to clear
an obstruction. Damages caused
while clearing or attempting to
clear blockages are not covered
under your product’s limited
warranty.
Unplug the vacuum
before checking for
blockages.
Reassemble all parts
securely before
operating vacuum.
1
2
3
1 DUST CUP AIR DUCT:
Stand vacuum upright.
Remove Dust Cup Assembly and
empty Dust Cup if necessary.
Check Air Duct behind Dust Cup
for clogs; clear before replacing
Dust Cup Assembly. (Fig. 20)
2 HOSE INTAKE OPENING:
Hold the top of the hose access
door and pull firmly to remove.
Slide the knob to the center and
pull out the hose. (Fig. 21)
Remove any obstructions and
push the hose back in.
Slide the knob to the left and
snap the hose access door shut.
3 HOSE:
Disconnect the Stretch Hose by
gently pressing the tabs together
and pulling away from the hose
connector.
Remove hose from both the unit
and handle ends. (Fig. 22)
Inspect the length of the hose
and remove any obstuctions.
Fig. 20
Fig. 21
Maintenance
Resetting the Motor Thermostat
Your Shark
®
Navigator
™
is equipped
with a protective Motor Thermostat.
If the motor should overheat, the
thermostat shuts off the power.
TO RESET THE MOTOR
THERMOSTAT:
Press the Power Button (
)to turn
the unit “Off”.
Unplug the vacuum.
Check for clogged hose or filter;
unclog hose and replace filter.
Refer to Checking for Blockages
on page 11.
Wait 45 minutes for vacuum to cool;
then plug in the vacuum.
Press the Power Switch ( ) to start
the vacuum.
NOTE: If vacuum still does not start,
contact Customer Service at:
1-800-798-7398.
To order Additional Parts &
Accessories go to
www.sharkclean.com.
PART PART NO.
Stretch Hose 126FFJ
Multi-Tool 127FFJ
Foam & Felt Filter XFL100
Extension Wand 1116-FC
24” Crevice Tool 122FFJ
11” Crevice Tool 129FFJ
Pet/Upholstery Tool 128FFJ
Get even more cleaning from your Shark
®
Navigator
™
by checking out our cleaning
accessories assortment at
www.sharkclean.com.
Bookmark the page and check back often
to take advantage of the latest products,
promotions and prices!
ADDITIONAL ACCESSORIES:
CREVICE TOOL
Reach deep into narrow spaces and clean between cushions,
under radiators and baseboards and in hard to reach crevices and
corners.
MULTI-TOOL
This unique tool combines a dusting brush and a crevice tool into
one.
PET/UPHOLSTERY TOOL
This tool will remove hair from upholstery and stairs.
NOTE: Some accessories may be included with your
purchase.
Fig. 22
NV100_26_IB_ENG_110317_2.indd 10-11 11-03-17 10:40 AM

   Find Your Products By Category