4.9

Out of 2 Ratings

Owner's of the Sebo Vacuum Cleaner X4 gave it a score of 4.9 out of 5. Here's how the scores stacked up:
  • Reliability

    5.0 out of 5
  • Durability

    5.0 out of 5
  • Maintenance

    4.5 out of 5
  • Performance

    5.0 out of 5
  • Ease of Use

    5.0 out of 5
of 14
 
Page 8
Changing the Dust Bag - Figure 7
To change the dust bag, pull the cover release flap forward
(#5 on page 5) and lift the cover (7) from the dust bag
housing. The cover release flap must remain in a for-
ward “pulled-out” position to change dust bags and
lock them into place. Squeeze the clamps on both sides
of the dust bag sealing plate, slide the plate (28) from the
holder (29) and push the cap on to seal the bag. Slide the
sealing plate (28) of a new bag into the holder and push it
in firmly. Re-insert cover into dust bag housing, push it for-
ward, then lock it in place by pushing down the cover
release flap. You may find it convenient to store the bag
cap inside the dust bag housing below the dust bag.
Changing the Micro-Hygiene Filter -
Figure 8
The micro-hygiene filter (30) needs to be changed when
it becomes extremely dirty or clogged with dust, or after
approximately 20 dust bags have been used. To change
the micro-hygiene filter, pull the cover release flap (#5 on
page 5) forward and lift the cover from the dust bag hous-
ing. Then, slide the filter out at the bottom.To replace, lift
the safety lever (31) and slide the new filter in using the
tracks as guides.
Changing the Brush Roller(s) -
Figure 10 (X4),Figure 10a (X5)
To change the brush roller(s) (35 or 35a), push the but-
ton(s) (36 or 36a), remove the side plate(s) (37 or 37a),
turn the brush(s) clockwise a quarter of a turn, and pull
the old brush roller(s) out. Slide the new brush roller(s)
into the brush housing and turn it until it locks into posi-
tion. While slightly pushing the button(s) (36 or 36a),
press the side plate(s) (37 or 37a) back into the locked
position.
Figure 7
Figure 8
Figure 9
Figure 10 (X4)
Figure 11 (X4)
Always unplug vacuum from outlet
before dismantling any part of machine!
!
Dust Bag
Part #5093 AM
Micro-Hygiene
Filter
Part #5036 AM
Exhaust Filter
Part #5143
Brush Roller (X4)
Part #5010 AM
Changing the Sealing Strip -
Figure 11 (X4),Figure 11a (X5)
The sealing strip (39) is located just behind the brush
roller opening. The sealing strip seals the power head to
hard floors to prevent kick-back of debris while vacuum-
ing. To replace a worn sealing strip, push the release but-
ton, remove the side plate (36 and 37 in figure 10 & 10a)
and slide old strip out. Insert the new strip into the slot
and slide into place.
Changing the Exhaust Filter - Figure 9
After 20 bags have been used, change the exhaust filter
(32). To remove the exhaust filter, push the catch (33)
backward and remove the filter cover (34) and exhaust fil-
ter. Insert the new filter and replace the filter cover.
39
Maintenance
Figure 10a (X5)
Figure 11a (X5)
Brush & Edge Rollers (X5)
Part #5290 AM
Sealing Strip
Part #5400-1 (X4)
Part #5400-2 (X5)

   Find Your Products By Category