0
Owner's of the Sebo Vacuum Cleaner K2 gave it a score of 0 out of 5. Here's how the scores stacked up:
10
To remove a brush or power head, switch off the power and unplug the vacuum. Then,
press the tool release button (7) and pull the tube out.
NOTE! K3 users with ET-H, ET-1 or ET-2 power heads, please refer to your power head
user’s manual for more detailed instructions for operating and maintaining your power
head.
Premium Parquet nozzle - Figure 13
The parquet nozzle (29) is specially designed for use on hard surfaces. The brush should be
cleaned regularly. Remove the parquet nozzle from the telescopic tube to clean. Fibers and
hair can be pulled out of the bristles manually, or vacuum the bristles with with the tele-
scopic tube. The brush strips are removable for cleaning and replacement.
Combination nozzle - Figure 14
The Combination nozzle (30) is adjustable for carpet or hard floors. To set for carpet, slide
the up arrow button (42) to the right until it clicks into place. The hard floor dusting brush
will raise up allowing the head to move over the carpet. To set for hard floors, slide the down
arrow button (43) to the left until it clicks into place. The brush will lower to gently sweep
your floors. The slider in Figure 14 is set in the position for hard floors. The brush should
be cleaned regularly. Remove the Combination nozzle from the telescopic tube to clean.
Fibers and hair can be pulled out of the bristles manually, or vacuum the bristles with with
the telescopic tube. The brush strip is removable for cleaning and replacement.
Turbo Nozzle - Figure 15
The Turbo nozzle (31) has an air-driven rotating brush for gentle brushing of carpets. The
Turbo nozzle can be adjusted for high and low pile carpet. To adjust the head for high pile
carpet, push the slider button (44) to the right. For low pile carpet, push the slider button
(44) to the left. The slider in Figure 15 is set in the low pile position. The rotating brush
should be cleaned regularly. Remove the Turbo nozzle from the telescopic tube to clean.
Remove fibers and hair from the brush manually.
The telescopic tube (4) is useful for vacuuming corners and hard-to-reach areas. You may
use the telescopic tube without a brush, power head or attachment. To remove a brush or
power head, switch off the power control knob (9) and unplug the vacuum. Then, press the
tool release button (7) and pull the tube out. The crevice nozzle (20) and dusting brush (28)
may be inserted onto the end of the tube. To use the upholstery nozzle (11), fit it onto the end
o
f the crevice nozzle (20). It is not necessary to turn off the vacuum while switching the stan-
dard attachments (the crevice nozzle, upholstery nozzle or dusting brush). After use, switch
off the power, unplug the vacuum and remove attachment. Re-insert the telescopic tube into
the power head or brush, turning the tube if needed, until you hear it click into place.
NOTE! K3 users with ET-H, ET-1 or ET-2 power heads, please refer to your power head
user’s manual for more detailed instructions for connecting your power head.
To use the hose without the telescopic tube, switch off the power and unplug the vacuum.
Push the handle release button (3) and pull the HANDLE out of the end of the telescopic tube.
Do not try to separate the hose from the handle! Insert the crevice nozzle (20) or dusting brush
(28) onto the end of the handle. To use the upholstery nozzle (11), fit it onto the end of the
crevice nozzle (20). After use, switch off the power, unplug the vacuum and remove the
attachment. Re-insert the handle into the telescopic tube making sure it is seated correct-
ly and snap it into place.
Figure 11
Figure 12
7
Using the Telescopic Tube, Hose & Attachments - Figures 11 & 12
4
Figure 13
Figure 15
Figure 14
43
Always unplug vacuum from outlet before dismantling
any part of machine!
!
USE AND MAINTENANCE OF BRUSHES AND HEADS
42
44
▲
▲
20
1
4
20
11
29
30
▲
▲
31
Find Your Products By Category
Please Login
